How to mix good homebrew juice:

Less IS MORE!!!! Always start with ur base of nic first, then add desired PG/VG, then slowly introduce drops of flavor. I recommend 2 drops, smell test, 2 more, taste and so on.

My staple technique was formulated on using the calculator on the net found here.

http://www.todmuller.com/ejuice/ejuice.php

This calculator is SPOT ON and lets even the noob create FANTASTIC home brews!!! But as mentioned above, easy on the flavor, until desired amount is achieved. Even a great mix calculation doesn’t know YOUR desired taste!

Also, mix in small batches, always! you can always double up but too much of anything leaves more room for error

When you have an atomizer that has low vapor production, is clogged or seams “dead” (but not cold), use a standard balloon, any balloon to blow the debris and clogged juices form the atty.

Here’s how:
1-Blow up balloon
2-Put mouth end of balloon around either side of atty, making sure the air can only escape thru the atty. Put balloon under ur arm and apply enough pressure that the balloon deflates w/out popping.
3-Repeat step 2 on other opening of atty.
4-repeat steps 2 and 3 until just clear air (no juice or debris) comes out.
5-Re-drip and vape on!

This has been a BLESSING to me, as well as many attys I “thought” were “dead”! No more soaks that eat the glues, no more overnite waiting on juice to seep out and best of all….THIS WORKS WONDERS ON CHANGING FLAVORS IN A JIFFY!!!

Try it!

Tips:
#1 If you have the electronic devices that have the manual switch, never
slip them into your pocket or do anything to activate them without your
knowledge. They will get very hot and not only burn you but also burns out
your atomizer.
#2 Clean your contacts with alcohol often as they corrode and will not
charge correctly.
#3 Buy the dc charger for travel. It works great!

I’ve almost left the house several times without grabbing my e-juice and had
to head back home to grab it. To keep me doing this anymore I got a little,
metal, key chain pill holder from the pharmacy that I can put a 3 ml bottle
in. Make sure you get one that will fit your bottle. If they are sold loose
(instead of a sealed blister pack) open them up and find one that fits.

Mine is a tight fit, but my bottle won’t bounce around inside it. Just make
sure you rotate out the juice every once in a while to keep it from going
bad. Using this, I can be sure I’ll never be without juice when I need it.

Mike, Madison, WI

How to clean a flooded atomizer (My personal method has worked on a 510,
Lucci and a volcano atomizer):

First take a small glass and put coca-cola in it (you really don’t need much
just enough to put your atty in). Then take a pair of tweezers and drop your
atty into the glass. Let the atty sit in there for approx 15-20 minutes with
occasional sturring just make sure that the carbonation works its way
through the atomizer. Then take the atomizer out of the glass with your
tweezers into a pan/pot with boiling water(again doesn’t have to be a lot of
water just enough to engulf the entire atty and enough so you won’t burn
your pan!!!). Let that sit for approx 15-20 as well. After that take either
your tweezers or, for more reluctant people, a pair of tongs that will
distance you from harm and put your atomizer on a plate or clean surface.
Then take a blow dryer and dry the entire atomizer for approx 30-90 seconds
or until you are satisfied that your atomizer is thoroughly dried. After you
have gone through this entire process I would personally wait quite awhile
before trying to use them or you will get a nasty, wet burnt taste because
of left over water excess. I did this process at night right before I went
to bed and woke up and my atty was as good as new!!! So I would say wait a
good 4-6 hours would be my estimated time. You can try to use it sooner but
I wouldn’t recommend it, but that is just me being on the safe side. I hope
that this was helpful. Happy vaping Everyone!!!

Kody

Tip: Wipe off your battery threads before placing them in the charger; that
way they wont transfer juice and guck to the charger. I find that this
actually improves the life of both the batteries, and the chargers.

Jacob
Cedar Rapids IA

1. Whether you buy a new e-cig for yourself or as a gift, buy a bottle [or
more] of e-liquid and extra atomizers.

2. If you have an e-liquid flavour you really don’t like add a little mint
or vanilla flavouring appropriate for vaping {LorAnn, Fairies Finest,
FlavourArt, etc.]

3. Always prime a new atomizer! You can use regular e-liquid or with a few
drops of plain PG or VG. Never vape a dry atty! It’s sure to kill it.

Shannon

My tip is to get yourself gear to charge your unit in the car. Some people
(like me) may have felt the USB PCC, AC Charger, and 4 batteries/attys were
sufficient to keep them vaping at all times, as they really aren’t out for
more than 3-4 hours per day. Recently, we had a power failure and I was
afraid I would be out of batteries before power was restored. I made it
through, but ordered the car charger the next day. Now I have the peace of
mind that if we lose power I’ll still be able to charge my Joye-510! By the
way, thanks for your awesome shipping. I placed an order at 11:00 on a
Saturday night and felt sure it wouldn’t get here until Wednesday because I
felt that you wouldn’t have been able to ship it until Monday, but somehow
it showed on Monday!! Nice work!! Thanks!

Tip from Susan from Michigan

To clean the atomizer, “spin” the ends of a cotton swab (Q-tip), around
between your thumb and pointer finger so there are no loose cotton
particles. Dip in rubbing alcohol and swab well around the inside of you
atomizer. The dry end of the swab may be used to remove any excess debris or
alcohol remaining. Rubbing alcohol dries very quickly so there will probably
be no need to dry, but if desired a hairdryer on cool setting may be used.
Atomizer “buzzes” like new!